濟南雕刻機在運行中要注意正確的方法

來源：http://www.dzxiaoche.com 時間：2021-06-21 

濟南雕刻機的使用率在逐年提高，甚遍及各個行業和領域，但也有因為發展迅速，設備操作中的一些細節問題往往被忽略，導致一些人在運行中出現各種問題。那么，大家知道設備在運用中要注意哪些方法和技巧嗎?下面墨源數控就為您介紹下具體的內容。

The utilization rate of Jinan engraving machine is increasing year by year, even throughout various industries and fields. However, due to the rapid development, some details of equipment operation are often ignored, leading to various problems in the operation of some people. So, do you know what methods and skills should be paid attention to in the use of equipment? The following ink source CNC will introduce the specific content for you.

1、使用之前檢查電機主軸冷卻中冷卻液的儲存量，開啟電機的主軸冷卻，保證冷卻液循環正常。開啟正壓密封，以避免加工廢液、冷卻液等進入電機主軸軸承。

1. Before use, check the coolant storage in the motor spindle cooling, turn on the motor spindle cooling, and ensure that the coolant circulation is normal. Open the positive pressure seal to prevent the processing waste liquid and coolant from entering the motor spindle bearing.

2、在雕刻過程中，切記帶上手套清理雕刻碎片，或觸摸雕刻主軸，主軸高速運轉，很容易在手套和手一起滾動，帶來隱患;

2. In the carving process, remember to wear gloves to clean up the carving debris, or touch the carving spindle, the spindle runs at high speed, it is easy to roll together in gloves and hands, which brings hidden danger;

3、使用濟南雕刻機雕刻時，在裝卸雕刻板時，須先卸下雕刻工具，以免鋒利的工具對操作者造成傷害。

3. When using Jinan engraving machine to carve, when loading and unloading the engraving board, the engraving tools must be removed first to avoid the sharp tools causing damage to the operator.

4、雕刻機的操作看似簡單，但也有很多操作要求和規范需要注意，上崗前須經過嚴格的培訓和考核，以免操作中出現失誤帶來麻煩。

4. The operation of engraving machine seems simple, but there are also many operation requirements and specifications need to be paid attention to. Before taking up the post, we must go through strict training and assessment, so as to avoid the trouble caused by mistakes in operation.

5、濟南雕刻機在使用過程中，不得隨意操作。如有故障，應先切斷電源，再進行維修，以免高速雕刻機對操作人員造成傷害;

5. Jinan engraving machine is not allowed to operate at will during use. If there is any fault, the power should be cut off first, and then the maintenance should be carried out, so as to avoid the injury of the high-speed engraving machine to the operators;

6、雕刻過程中，嚴禁近距離觀察，以防切屑飛入眼睛。觀察時要暫停雕刻，關閉電機主軸并確定電機主軸不再旋轉。雕刻過程中，嚴禁用手摸切削表面，禁止使用棉絲擦拭工作表面。

6. In the process of carving, close observation is strictly prohibited to prevent chips from flying into the eyes. Pause engraving during observation, close the motor spindle and make sure that the motor spindle does not rotate any more. In the process of carving, it is forbidden to touch the cutting surface with hands and wipe the working surface with cotton thread.

7、雕刻前要認真檢查所使用刀具的尺寸，性能是否滿足加工編程要求。

7. Before carving, carefully check the size and performance of the cutting tools to meet the requirements of machining programming.

8、每天下班前10分鐘，對機床加油潤滑及擦洗清潔機床。確認機床停止運轉，將機床停在指定位置，關閉電源，確認所有開關己斷開，方可離開。

8. Lubricate and clean the machine tool 10 minutes before work every day. Confirm that the machine tool stops running, stop the machine tool at the designated position, turn off the power, and confirm that all switches have been disconnected before leaving.

建議用戶在使用濟南雕刻機進行工作之前，要有一定的經驗技術，參加過技術培訓，以免操作中因為操作不當、不熟練等問題，導致設備出現故障或者給人身健康帶來傷害。不清楚方法的用戶可以參考上述內容進行使用，以便雕刻機能充分發揮其作用。

It is suggested that users should have certain technical experience and participate in technical training before using Jinan engraving machine, so as to avoid equipment failure or personal health injury due to improper operation and unskilled operation. Users who are not clear about the method can refer to the above content for use, so that the engraving function can give full play to its role.

• 上一篇：雕刻機的干擾問題怎么解決？
• 下一篇：木工雕刻機故障如何預防？

相關產品：
• 
  木工雕刻機
• 
  1325木工雕刻機獨...
• 
  1325木工雕刻機
• 
  1325木工鏤空花格...
• 
  1225型平雕圓雕一...

相關新聞：
• 
  激光雕刻機和機械雕刻...
• 
  三軸雕刻機無心外圓磨...
• 
  石材雕刻機斷刀的原...
• 
  數控開料機會受到什么...
• 
  泡沫雕刻機日常井蓋如...